PO47-1S gunners control panel theory

-

 

Preparation for combat.

The action of the gunner-operator in preparation for firing in the daytime with standard weapons and the installation of the operator's console


The action of the gunner-operator in preparation for shooting during the day with standard weapons.


At the command of the tank commander to prepare for firing or independently after loading ammunition, the gunner-operator performs the following actions.


Turn on the switches on the gunner's console in the following order:


Toggle switches Top row:

  • Ballistics computer (2nd on the left) Converter (4th on the left)

Bottom row toggle switches:

  • Rangefinder (1st on the left)

  • Autoloader (3rd on the left)


After that, the gunner reports to the commander on the readiness for battle. and the gunner begins to monitor the appearance of targets.

Installation of the operator console.

  1. While holding the remote control (2), connect the plug connectors (1) and (6), secure them with the cap nuts.


  1. Install the remote control (2) on the pre-made rivet nut and secure it with bolts with flat and spring washers. Wire the cap nuts of the plug connectors.


  1.  Turn on the battery switch and check the readiness of the remote control for operation, for which the corresponding switches are turned on and off sequentially, while the luminous inscriptions on the display should light up and go out.


  1. Check the display of the label PALLET: 


  • Disable AUTOLOADER ELECTRICAL. DESCENT on the right distributor, on the control panel and turn it on again


  • Turn on switch 3, perform an automatic charging cycle


  • Turn on the GUN STOP switch on the Autoloader control panel


  • Open the wedge, after which the glowing label PALLET should light u


  • Press the button of the catcher lock switch with your hand, the illuminated label should go out.



Taken from: "Войсковой ремонт ч1к2" - "Military repair Part 1, Book 2"


Comments

Post a Comment

Popular posts from this blog

"AGAVA" - "AGAVA-2" and its confusing history

-
Image
When covering Soviet sight technology there are always some interesting designs and approaches to solving an issue. It is a common fact that the Soviet Union in the 1980s-1990s was quite behind in thermal sight technology. Only in the 1990s, but to be specific in 1992, the Soviet Union now Russia started to field small batches of thermal sights on their tanks, primarily T-80Us and some of the early T-90 variants, which just recently entered service. Russia's journey through creating its own domestic thermal sight traces back to 1982.  The 1980s were quite an important time for the 'Krasnogorsk Factory named after S.A Zverev', which is still to date an Optical Engineering and Optoelectronics factory. The factory is primarily known for making domestic Soviet cameras back in the day. However, that's not the only thing that the factory has produced back then.  Close to the mid-1980s, the facility was contracted to develop new thermal sight technology for the Soviet Ministry...
Read more

T-90A - a short history of sights

-
Image
  In 2004, the T-90A (Object 188A1) tank joined the Russian armed forces. It included many fire control system upgrades, a new welded turret, and improved mobility. The T-90A Obr. 2004 tank was fitted with a T01-K05 Buran-M Obr. 2004 3rd generation night vision sight, which improved over the previous T01-K01 Buran-PA sight from the T-90 Obr. 1992. --Picture of T-90A with Buran-M Obr. 2004-- In 2005, the tank received an upgrade for the sight, which became T01-K05 Buran-M Obr. 2005, with noticeable differences in the sight's housing. --Picture of T-90A with Buran-M Obr. 2005-- --Picture of T-90A diagram with Buran-M Obr. 2005-- --Picture of two T-90As, one with Obr. 2004 and one with Obr. 2005 Buran-M sights-- Above: T-90A with Buran-M Obr. 2004 sight, and behind it, T-90A with Buran-M Obr. 2005 sight. In 2006, the T-90A had to be brought to more modern standards, so the production of this model with new second-generation thermal imaging sight began. The sight was named ESSA, wh...
Read more

Object 490 "Тополь" - "Poplar"

-
Image
      The project of a promising tank developed in the 1980s by E.A. Morozov. Object 490 "Тополь" - "Poplar" mockup                          The design had some primary characteristics which are worth mentioning. A crew consisting of two people - the gunner commander and the driver.  Reducing the crew to two and placing them in a compact, well-protected capsule.  The use of a hydropneumatic suspension.  In addition to solving the main task - increasing average speeds by improving the smoothness characteristic, it makes it possible to control the tank's clearance, which increases the manoeuvrability and survivability in battle.  In addition, the controlled hydropneumatic suspension by changing the trim of the machine allows you to increase the gun pointing angles in the vertical plane. Reducing the crew to two people and placing them in a compact, well-protected capsule with the ...
Read more